www.dmgmori.com NT4200 DCG NT4250 DCG NT4300 DCG NT5400 DCG High-Precision, High-Efficiency Integrated Mill Turn Center NT Series

3 2 3 4 5 6 7 Industrial machinery Medical equipment 1 2 Turbine blade Drive shaft Automobiles 3 4 Cylinder head Crank shaft 5 6 Hip joint Knee joint Aerospace 7 Landing gear

5 Simultaneous 5-axis machining ++ Simultaneous 5-axis machining of complex parts with the direct drive motor (DDM) installed in the B axis ++ B-axis rotation range 120 Ease of operation ++ Digital tailstock equipped as standard + Movable swivel operation panel for comfortable setups High precision ++ High-speed, high-accuracy machining achieved by NT series original Box in Box structure and Driven at the Center of Gravity ++ Tool spindle: Higher cutting performance and machining accuracy with 2-face contact Capto specification ++ ORC (Octagonal Ram Construction) as a solution for heat control to ensure high-speed, high-accuracy feed Peripheral equipment ++ Compatible with automation systems including a gantry loader and a robot Energy-saving ++ Power-saving setting and reduction in consumption of lubricating oil MAPPS: Mori Advanced Programming Production System

: Standard Tool spindle : Option Tool spindle B-axis Tool spindle Milling Turret 2 Tool spindle Y-axis Turret 2 Milling Spindle 1 Spindle 2 Tailstock When spindle 2 (S2) is selected, the tailstock (TS) is not provided. Specifications An extensive line-up to handle a wide range of workpiece sizes. NT4200 DCG Chuck size 8-inch NT4250 DCG Chuck size 10-inch NT4300 DCG Chuck size 12-inch NT4200 DCG/1000 NT4200 DCG/1500 NT4250 DCG/1000 NT4250 DCG/1500 NT4300 DCG/1000 NT4300 DCG/1500 NT5400 DCG Chuck size 15-inch NT5400 DCG/1800 2 models 2 models 7 2 models 1 models Tailstock specification Spindle 2 specification Tool spindle Tool spindle Spindle 1 Tailstock Spindle 1 Spindle 2 Turret 2 Basic specification Optional specifications Tool spindle / Spindle 1 Spindle 2 Turret 2 <Without the milling function> Turret 2 <Milling specifications> Tailstock : Standard　: Option　: Not applicable Turret 2

: Standard Tool spindle : Option Tool spindle B-axis Tool spindle Milling Turret 2 Tool spindle Y-axis Turret 2 Milling Spindle 1 Spindle 2 Tailstock When spindle 2 (S2) is selected, the tailstock (TS) is not provided. Workpiece size 9 Max. turning length Max. turning diameter Basic specification Optional specifications /1000 /1500 Max. turning diameter mm (in.) Tool spindle: Capto C6 φ660 (φ25.9) / Turret 2: φ350 (φ13.7) NT4200 DCG Max. turning length mm (in.) 1,081 (42.5) 1,061 (41.7) 1,596 (62.8) 1,576 (13.7) Bar work capacity mm (in.) 65 (2.5) 65 (2.5) / 65 (2.5)＊2 65 (2.5) 65 (2.5) / 65 (2.5)＊2 Max. turning diameter mm (in.) Tool spindle: Capto C6 φ660 (φ25.9) / Turret 2: φ350 (φ13.7) NT4250 DCG Max. turning length mm (in.) 1,047 (41.2) 1,027 (40.4) 1,562 (61.4) 1,542 (60.7) Bar work capacity mm (in.) 80 (3.1) 80 (3.1) / 80 (3.1)＊2 80 (3.1) 80 (3.1) / 80 (3.1)＊2 Max. turning diameter mm (in.) Tool spindle: Capto C6 φ660 (φ25.9) / Turret 2: φ350 (φ13.7) NT4300 DCG Max. turning length mm (in.) 1,003 (39.4) 983 (38.7) 1,518 (59.7) 1,498 (58.9) Bar work capacity mm (in.) 90 (3.5) 90 (3.5) / 90 (3.5)＊2 90 (3.5) 90 (3.5) / 90 (3.5)＊2 Basic specification Optional specifications Max. turning diameter NT5400 DCG Max. turning length Bar work capacity mm (in.) mm (in.) mm (in.) ＊2 Spindle 2 /1800 Tool spindle: Capto C6 φ920 (φ36.2) / Turret 2: φ470 (φ18.5) 1,921 (75.6) 103 (4.0) / 103 (4.0)＊2

11 1 2 3

Cooling of tool spindle The oil jacket spirally arranged around the spindle unit prevents the spindle temperature from rising. Ball screw core cooling The ball screw core cooling system controls temperature rise in ball screws. Cooling oil is circulated inside the hole at the center of ball screws to control heat generation. The cooling oil is also circulated inside the motor base to prevent motor heat from transmitting to machine casting bodies. Coolant chiller <separate type> (Option) Raised coolant temperature causes thermal displacement in the fixtures and workpiece, affecting the machining accuracy of the workpiece. Use this unit to prevent the coolant from heating up. When using oil-based coolant, the coolant temperature can become extremely high even with the standard coolant pump, so please be sure to select this unit. When using oil-based coolant or a super-high-pressure coolant system, please be sure to consult our sales representative. We cannot guarantee that this unit will completely control the coolant temperature. It is designed to help prevent oil temperature increases. Direct scale feedback (Option) No contamination of the measuring system to oil or water condensation. + Superior precision with the Magnescale absolute linear + Impact resistance of 450 m/s2 (17,716.5 in./s2) measuring system featuring a standard resolution of 0.01 µm + High-resolution, magnetic measuring system + Resistance to oil and condensation due to a magnetic detection principle + Vibration resistance of 250 m/s2 (9,842.5 in./s2) + Thermal expansion coefficient as cast iron 13

Spindle 1 / Spindle 2 (Option) Min. indexing increment: 0.0001˚ Chuck size Max. spindle speed [　] Option ＊ High output NT4200 DCG NT4250 DCG NT4300 DCG NT5400 DCG inch min-1 8 10 12 15 5,000 [5,000＊] 4,000 [4,000＊] 3,000 [3,000＊] 2,400 [2,400＊] Symmetrical structure The high-speed Spindle 1 and the rotary tool spindle on Turret 2 (option) are arranged symmetrically to uniformly conduct heat to both sides. The thick casting structure ensures high rigidity and minimize thermal displacement to keep high-accuracy machining. Tailstock (Tailstock specification) The NT series comes standard with a servo-motor driven, high-rigidity digital tailstock, which drastically reduces setup time. (except for the Spindle 2 specification) Photo: NT4250 DCG/1500 Simultaneous operation of Spindle 1 and Spindle 2 <Spindle 2 specification> (Option) Milling and turning can be simultaneously done on Spindle 1 and Spindle 2, which ensures accurate machining of long and narrow workpieces. As workpieces can be transferred between the spindles, the transfer to the next process is easily done, achieving higher machining efficiency. 15

: Standard Tool spindle : Option Tool spindle B-axis Tool spindle Milling Turret 2 Tool spindle Y-axis Turret 2 Milling Spindle 1 Spindle 2 Tailstock When spindle 2 (S2) is selected, the tailstock (TS) is not provided. Driven at the Center of Gravity The machine body is driven at the center of gravity to control vibration, the biggest barrier to high-speed, high accuracy machining. Residual vibration comparison X-axis ) m µ ( e d u t i l p m a n o i t a r b i V 10 8 5 4 2 0 22 24 25 28 210 Rapid traverse rate 100% (stopped in the X2axis direction) Z-axis 0.4 0.45 0.5 0.55 Time (sec.) Driven at the Center of Gravity Machining by a Conventional Machine Effects of DCG + Improved surface quality + Outstanding acceleration + Improved roundness + Longer tool life DCG: Driven at the Center of Gravity A revolutionary structure which controls thermal displacement and offers outstanding straightness Square guides' excellent damping characteristics The 4 guideways are located diagonally from each other, so they distort symmetrically in response to the heat generated by high-speed travel. This means that the center stays in the same position, offering high-speed, high-precision feed. 17 400 mm (15.7 in.) Thermal displacement Heat generation The center stays the same Effects of ORC + Superior damping characteristics + Controls thermal displacement + Achieves high-speed, high-precision feed ORC: Octagonal Ram Construction Peeling (Tool spindle) We deliberately slowed down the feed, which normally causes a fine separation of chips, and concentrated on producing chips in one continuous strip. With this, high rigidity in the machine, tool, cutting tool and material can all be achieved, in addition to a shiny cutting surface. Chips are purposely not submitted to “chip control” during machining. NT4200 DCG/1000 Peeling Material <JIS>: S45C＊1 Cutting speed Feedrate Depth of cut m/min (fpm) mm/rev (ipr) mm (in.) 100 (328.1) 0.1 (0.004) 11 (0.4) ＊1 Carbon steel: 10451046 (ANSI), C45C45EC45R (BS, DIN), 45 (GB) The cutting test results indicated in this catalog are provided as examples. The results indicated in this catalog may not be obtained due to differences in cutting conditions and environmental conditions during measurement. ＝VibrationHeat generated by frictionLubricating oil outflowLubricating oil＝The lubricating oil in the oil pockets which were made by scraping is forced in and out through the gaps because of the contact pressure caused by vibration, generating heat.Vibration is reduced by converting vibrational energy into heat energy. This helps control chattering caused by vibration.

Two-face contact specification Flexural rigidity of tools has been improved by the contact with both the spindle taper and the end face. This extends tool life and improves cutting performance and machining accuracy. Capto specifications BT specifications HSK specifications KM specifications Constraining surface Constraining surface Constraining surface Constraining surface When selecting the two-face contact tool specification, be sure to use a two-face contact tool. DMG MORI builds all the spindles in house. SVC function <Equipped as standard on F31iA5 and F31iB5 only> The SVC function reads the program commands for tool tip control in advance and performs automatic compensation to achieve smooth tool feed. The combination use with the DDM (Direct Drive Motor) ensures higher surface quality and shorter cycle time in 5-axis machining. 19 Motion of the SVC function OFF ON The SVC function includes the following functions + AI contour control + Nano smoothing + Smooth TCP + Machining mode selection + G332 tolerance command Workpiece Workpiece Tool center point (TCP) control <Equipped as standard on F31iA5 and F31iB5 only> Gage line Main features et gth offs ol le To n Cutter radius compensation + The tool path can be controlled from the tool center point. + No reprogramming is needed when the tool length and the tool diameter are changed. Tool center point + NC automatically calculates cutter radius compensation and tool length offsets based on the program commands for tool tip control.

Turret 2 Number of tool stations Max. rotary tool spindle speed Turret indexing time (1-station) Milling capability NT4200 DCG NT4250 DCG 12 NT4300 DCG NT5400 DCG 10 6,000 0.28 0.31 min-1 sec. The Turret 2 with a coupling diameter of 250 mm (9.8 in.) and higher rigidity can perform face milling of up to φ 80 mm (3.1 in.) workpieces. It is equivalent to cutting performance of No.40 taper spindle machining centers. The milling specification is capable of heavy duty cutting as powerful as the tool spindle, achieving higher productivity and process integration. Face mill φ80 mm (φ3.1 in.) Sufficient work envelope for the tool spindle <NT 4250 DCG/1500> Sufficient area is secured for machining even when the tool spindle is located in-between spindle 1 and spindle 2. 113 (4.4) 330 (13.0) 150 (5.9) 171.2 (6.74) 500 (19.7) 460 (18.1) 113 (4.4) 1,862 (73.3) 0 2 3 φ . ) 6 2 1 ( 24.8 (1.0) 0 3 ) 2 1 ( . 0 9 ) 5 3 ( . . ) 9 4 ( 5 2 1 21 Mature and Evolved BMT Technology <Turret 2 milling specification> The built-in structure, in which the motor is placed inside the turret, minimizes heat generation and vibration, improves transmission efficiency and significantly increases cutting power, speed and accuracy. Effects of the BMT + Improved milling power + Improved milling accuracy + Controls the turrets heat and vibration + Reduced energy loss + Turret temperature increases: Compared with conventional machine 1/10 or less + Vibration amplitude: Compared with conventional machine 1/3 or less BMT: Built-in Motor Turret

Super-high pressure coolant system (Option) Coolant chiller (Option) Mist collector (Option) Hydraulic chuck (Option) Coolant gun (Option) Coolant float switch (Option) 23 DMQP (Option) The DMQP program is designed to certify peripherals that meet DMG MORI standards in quality, performance and maintainability. DMQP provides customers with even greater peace of mind. Comprehensive support with machineperipherals DMQP Coolant gun Coolant chiller Mist collector Service Center Machine + Qualified peripherals are arranged by DMG MORI + Toll-free phone support is available 24 hours a day, 365 days a year (Japan only) For more details on DMQP items, please consult our sales representative. DMQP: DMG MORI Qualified Products

Gantry-type loader system (Option) <Consultation is required> Parallel hands Back end double hands For these models NT4200 DCG NT4250 DCG NT4300 DCG Gantry loader standard accessory / specification ++ 10-station rotary workstocker (LG-10) ++ Hand airblow ++ Chuck air-blow ++ Automatic power-off system ++ Workpiece counter (PC counter) ++ Spindle orientation ++ Low air pressure detecting switch LG-10 (machine travel type) X-axis <Hand moves up and down> m/min (fpm) 90 (295.3) Z-axis <Loader moves right and left> m/min (fpm) Gantry loader Max. travel speed Applicable workpiece size Outer diameter mm (in.) Work stocker Number of pallet tables Max. loading capacity Max. workpiece stacked height Hand type Loader hand Outer diameter Applicable workpiece size Length Max. mass kg (lb.) / Pallet mm (in.) mm (in.) mm (in.) kg (lb.) 120 (393.7) φ40200 (φ1.67.9) 10 20 75 (165) 470 (18.5) Back end hand φ40200 (φ1.67.9) 20150 (0.85.9) 10 [ ] Option Please consult with our sales representative in the case that a workpiece diameter is less than 40 mm (1.6 in.), or a workpiece length is less than 20 mm (0.8 in.). Parts catcher (Option) <NT4000 Series> 25 In-machine traveling type, Hand Workpiece conveyor <For shafts> Max. transfer weight Maximum workpiece diameter Maximum workpiece length kg (lb.) mm (in.) mm (in.) 4 (8.8) φ75 (φ2.9) 180 (7.0) In-machine traveling type, Workpiece receiver Workpiece conveyor <For flanges> Max. transfer weight Maximum workpiece diameter Maximum workpiece length kg (lb.) mm (in.) mm (in.) Feed rate (Z-axis direction) m/min (fpm) 4 (8.8) φ75 (φ2.9) 180 (7.0) 100 (328.1) Parts catcher Bar feeder system (Option) <Consultation is required> Integrated machining of bar materials can be achieved in combination with a parts catcher. The workpiece attachment/detachment system nor turnover system is not necessary. Recommended accessories for bar feeder specification ++ Bar feeder ++ Multi counter ++ Signal light ++ Guide bushing ++ Work stopper The picture may look different from an actual machine. The chip conveyor is right disposal only.

1 Magazine 4 Fully opening cover Full opening covers are used on the left side of the door for better maintainability. For the NT Series, you can choose the ideal one from a wide variety of tool magazine. Tool storage capacity Chain-type 20 [40, 80, 100] Rack-type [139, 179, 239] [ ] Option 2 MAPPS magazine operation panel 5 Equipment layout MAPPS magazine operation panel Machine side 27 Tool setup position Tool information can be viewed and edited at the setup Equipment that requires daily and/or regular position. Operators don't need to move back and forth inspection is placed at one place. The supply port between a machine and the operation system, which of lubricating oil is arranged at the lower part of improves workability. The tool management function option is required. the machine for easy oil supply. 3 Movable Swivel-type operation panel 120 The operation panel can be moved to right and left sides. The stoppers are set at every 15 degrees on the swiveling-type panel to prevent it from swinging during operation.

Conversational automatic programming function This function allows users to create programs simply by following the guidance on the screen. Much of the programming process has been simplified due to the minimal key entry required for even the most complex shapes. Machining menu List display function Contour input Simple soft jaw forming function Relief machining (Option) DXF import function (Option) 29 3D interference checking function Interference between items such as the spindle, workpiece, soft jaw, tool, holder and turret can be checked in 3D. If interference is detected, the machine will stop operation regardless of whether it is in the automatic or manual mode, providing the highest level of protection against interference. Interference detected Machine stops automatically Collisions can be avoided not only during program operation but also during setup. The 3D interference checking function will check for interference accurately as long as the 3D model exactly matches the actual configuration of the spindles, workpieces, soft jaws, tools, holders and turrets. Customized design is required for special shape. A cutting simulation that shows how material is removed as machining proceeds cannot be carried out during a 3D interference check. Fixed-point in-machine camera (Option) Images taken by cameras installed inside/outside the machine can be viewed on the programming screen. This function is useful for maintenance. Examples of camera locations ++ Inside machine (to check machining) ++ Tool magazine (to check cutting tools) ++ Chip bucket (to check chip accumulation)

NT Series General view NT4200 DCG / NT4250 DCG / NT4300 DCG ＊1 NT4200 DCGNT4250 DCGNT4300 DCG/1000 ＊2 NT4200 DCGNT4250 DCGNT4300 DCG/1500 Front view 4811 (189.4)＊1　5326 (209.7)＊2 Spindle center E Side view 3264 (128.5)＊1　3264 (128.5)＊2 620 (24.4) B A 65 (2.6) Spindle center E C D mm (in.) G F Q50705E04 Q50706E04 Q50759C04 Q50760C04 Width Discharge height Height to spindle center A: Standard B: EN type C: Standard D: EN type E Machine height G＊ F 31 Hinge type mm (in.) 1,152 (45.4) 1,400 (55.1) 1,076 (42.4) 956 (37.6) 1,365 (53.7) 2,793 (110.0) 2,927 (115.2) Hinge type Scraper type Drum filter type mm (in.) 1,790 (70.5) 2,019 (79.5) 1,063 (41.9) 1,021 (40.2) 1,394 (54.9) 2,822 (111.1) 2,956 (116.4) ＊Tool storage capacity 100 tools EN: European NormEuropean Standards NT5400 DCG Front view 6605 (260.0) Side view 4492.6 (176.9) B A 670 (26.4) Spindle center Spindle center E E C D F Q50886B04 Q50941B01 Width Discharge height Height to spindle center Machine height A: Standard B: EN type C: Standard D: EN type E F Hinge type mm (in.) 1,327 (52.2) 1,573 (61.9) 1,076.5 (42.4) 956 (37.6) 1,490 (58.7) 3,458 (136.1) Hinge type Scraper type Drum filter type mm (in.) 2,012 (79.2) 2,241 (88.2) 1,069 (42.1) 1,016 (40.0) 1,519 (59.8) 3,461 (136.3) EN: European NormEuropean Standards

: Standard Tool spindle : Option Tool spindle B-axis Tool spindle Milling Turret 2 Tool spindle Y-axis Turret 2 Milling Spindle 1 Spindle 2 Tailstock When spindle 2 (S2) is selected, the tailstock (TS) is not provided. NT4250 DCG/1000NT4250 DCG/1500 mm (in.) mm (in.) mm (in.) mm (in.) mm (in.) mm (in.) Tool spindle: Capto C6 φ660 (25.9)　Turret 2: φ350 (13.7) 730 (28.7) 1,047 (41.2) < /1000>　1,562 (61.4) < /1500> 1,027 (40.4) < /1000>　1,542 (60.7) < /1500> 80 (3.1) <Spindle 1> 80 (3.1) / 80 (3.1) <Spindle 1 / Spindle 2> 750 (29.5) <625 125 (24.6 4.9)> / 210 (8.3) 1,120 (44.1) 100 (3.9) < /1000>　1,550 (61.0) 100 (3.9) < /1500> 120 min-1 4,000 [High output: 4,000] <Spindle 1> 4,000 [High output: 4,000] <Spindle 1 / Spindle 2> JIS A 2-8 <Spindle 1> JIS A 2-8 <Spindle 1 / Spindle 2> Basic specification Optional specifications Capacity Max. swing of workpiece Max. turning diameter Max. turning length Bar work capacity Travel X-axis travel / Y-axis travel <Tool spindle> Z-axis travel <Tool spindle> for ATC B-axis rotation range <Tool spindle> Spindle 1 / Spindle 2 (Option) Max. spindle speed Spindle nose Tool spindle <Turret 1> Min. B-axis indexing increment Max. tool spindle speed Taper hole of tool spindle Tool storage capacity Max. tool diameter <With adjacent tools / Without adjacent tools> Max. tool length Max. tool mass Turret 2 (Option) Number of tool stations Shank height for square tool Max. rotary tool spindle speed Tailstock min-1 mm (in.) mm (in.) kg (lb.) mm (in.) min-1 1[0.0001] 12,000 Capto C6 [BT40＊] [HSK-A63 (T63)] [KM-63] Chain type: 20 [40, 100] Rack type: [179, 239] 70 (2.7) / 140 (5.5) 400 (15.7) 8 (17.6) [10 (22.0)] 12 25 (1.0) 6,000 33 12 25 (1.0) 6,000 Taper hole of tailstock spindle Live center (MT5) [Built-in center (MT4) ] Feedrate Rapid traverse rate Motors Spindle 1 drive motor <30 min / cont> Spindle 2 drive motor <30 min / cont> Tool spindle drive motor <10 min / cont> Turret 2 rotary tool spindle drive motor <5 min / cont> Machine size Machine height (From floor) m/min (fpm) min-1 kW (HP) kW (HP) kW (HP) kW (HP) Tool spindle X: 50 (164.1) Y: 30 (98.4) Z: 50 (164.1) Turret 2 X: 30 (98.4) Z: 30 (98.4) Spindle 2 A: 30 (98.4) B: 40 [100] C: 250 22 / 18.5 (30 / 24.7) [26 / 22 (34.7 / 30)] [22 / 18.5 (30 / 24.7)] [26 / 22 (34.7 / 30)] 18.5 / 11 (24.7 / 15) 5.5 / 3.7 (7.5 / 5) 5.5 / 3.7 (7.5 / 5) mm (in.) Hinge type Scraper type Drum filter type: 2,822 (111.1) [2,956 (116.4): Tool storage capacity: 100] Hinge type: 2,793 (110.0) [2,927 (115.2): Tool storage capacity: 100], Width (Machine Chip conveyor) mm (in.) Depth (Includes operation panel) mm (in.) Floor space Control unit < /1000>: 4,811 (189.4) [A: 1,152 (45.4)]　4,811 (189.4) [B: 1,400 (55.1)] < /1500>: 5,326 (209.7) [A: 1,152 (45.4)]　5,326 (209.7) [B: 1,400 (55.1)] 4,811 (189.4) [C: 1,790 (70.5)]　4,811 (189.4) [D: 2,019 (79.5)] 5,326 (209.7) [C: 1,790 (70.5)]　5,326 (209.7) [D: 2,019 (79.5)] 3,264 (128.5) FANUC A: Hinge type (Standard) B: Hinge type (EN type) C: Hinge type Scraper type Drum filter type (Standard) D: Hinge type Scraper type Drum filter type (EN type) [ ] Option ＊When selecting the two-face contact tool specification, be sure to use a two-face contact tool. Bar work capacity: Depending on the chuck/cylinder used and its restrictions, it may not be possible to reach full bar work capacity. Max. spindle speed, Max. rotary tool spindle speed: Depending on restrictions imposed by the workpiece clamping device, F31iB / F31iB5 fixture and tool used, it may not be possible to rotate at the maximum spindle speed. The information in this catalog is valid as of May 2017.

: Standard Tool spindle : Option Tool spindle B-axis Tool spindle Milling Turret 2 Tool spindle Y-axis Turret 2 Milling Spindle 1 Spindle 2 Tailstock When spindle 2 (S2) is selected, the tailstock (TS) is not provided. NT5400 DCG/1800 Tool spindle: φ920 (φ36.2)　Turret 2: φ470 (φ18.5) 920 (36.2) 1,921 (75.6) 103 (4.0) 1,040 (40.9) <850 190 (33.5 7.5)> / 255 (10.0) 1,940 (76.4) 200 (7.9) 120 mm (in.) mm (in.) mm (in.) mm (in.) mm (in.) mm (in.) min-1 2,400 [High output: 2,400] <Spindle 1> 2,400 [High output: 2,400] <Spindle 1 / Spindle 2> JIS A 2-11 <Spindle 1> JIS A 2-11 <Spindle 1 / Spindle 2> Basic specification Optional specifications Capacity Max. swing of workpiece Max. turning diameter Max. turning length Bar work capacity Travel X-axis travel / Y-axis travel <Tool spindle> Z-axis travel <Tool spindle> for ATC B-axis rotation range <Tool spindle> Spindle 1 / Spindle 2 (Option) Max. spindle speed Spindle nose Tool spindle <Turret 1> Min. B-axis indexing increment Max. tool spindle speed Taper hole of tool spindle Tool storage capacity Max. tool diameter <With adjacent tools / Without adjacent tools> Max. tool length Max. tool mass Turret 2 (Option) Number of tool stations Shank height for square tool Max. rotary tool spindle speed Tailstock min-1 mm (in.) mm (in.) kg (lb.) mm (in.) min-1 1[0.0001] 8,000 Capto C8 [BT50＊] [HSK-A100 (T100)] Chain type: 20 [40, 80] Rack type: [139, 179] 120 (4.7) / 250 (9.8) 600 (23.6) 30 (66.0) 10 25 (1.0) 6,000 35 10 25 (1.0) 6,000 Taper hole of tailstock spindle Live center (MT5) [Built-in center (MT4) (MT5)] Feedrate Rapid traverse rate Motors Spindle 1 drive motor <30 min / cont> Spindle 2 drive motor <30 min / cont> Tool spindle drive motor <30 min / cont> Turret 2 rotary tool spindle drive motor <5 min / cont> Machine size Machine height (From floor) Width (Machine Chip conveyor) Depth (Includes operation panel) Floor space Control unit m/min (fpm) Tool spindle X: 40 (131.2) Y: 30 (98.4) Z: 40 (131.2) Turret 2 X: 30 (98.4) Z: 30 (98.4) Spindle 2 A: 24 (78.7) min-1 kW (HP) kW (HP) kW (HP) kW (HP) mm (in.) mm (in.) mm (in.) B: 23.8 [80] C: 250 37 / 30 (50 / 40) [45 / 37 (60 / 50)] [37 / 30 (50 / 40)] [45 / 37 (60 / 50)] 30 / 22 (40 / 30) 5.5 / 3.7 (7.5 / 5) 5.5 / 3.7 (7.5 / 5) Hinge type: 3,458 (136.1), Hinge type Scraper type Drum filter type: 3,487 (137.3) 6,605 (260.0) [A: 1,327 (52.2)] 6,605 (260.0) [B: 1,573 (61.9)] 6,605 (260.0) [C: 2,012 (79.2)] 6,605 (260.0) [D: 2,241 (88.2)] 4,492 (176.9) FANUC A: Hinge type (Standard) B: Hinge type (EN type) C: Hinge type Scraper type Drum filter type (Standard) D: Hinge type Scraper type Drum filter type (EN type) [ ] Option ＊When selecting the two-face contact tool specification, be sure to use a two-face contact tool. Bar work capacity: Depending on the chuck/cylinder used and its restrictions, it may not be possible to reach full bar work capacity. Max. spindle speed, Max. rotary tool spindle speed: Depending on restrictions imposed by the workpiece clamping device, F31iA / F31iA5 fixture and tool used, it may not be possible to rotate at the maximum spindle speed. The information in this catalog is valid as of May 2017.

: Standard Tool spindle : Option Tool spindle B-axis Tool spindle Milling Turret 2 Tool spindle Y-axis Turret 2 Milling Spindle 1 Spindle 2 Tailstock When spindle 2 (S2) is selected, the tailstock (TS) is not provided. :Standard :Option :Consultation is required :Not applicable : Select one NT4200 DCG NT4250 DCG NT4300 DCG 37 Basic specification Optional specifications Magazine Tool storage capacity Coolant Coolant system Chip disposal Chip conveyor Measurement 20 tools 40 tools, 100 tools, 180 tools, 240 tools 800 / 1,100W (50 / 60Hz) <Tool spindle> 800 / 1,100W (50 / 60Hz) <Turret 2)> Right disposal, Hinge type Right disposal, Hinge type Scraper type Drum filter type Manual in-machine tool presetter Automatic in-machine tool presetter Other Chuck foot switch Spindle 1 (removable) Spindle 2 (removable) Tool spindle Turret 2 1 foot switch 2 foot switches Manual pulse generator (separate type) Signal light 3 layers (Red, Yellow, Green) LED Type ＊DMQP (DMG MORI Qualified Products) ＊1 When selecting the two-face contact tool specification, be sure to use a two-face contact tool. DMQP: Please see Page 23 for details. Full indexing specification B-axis: with the F31iA, up to four axes can be controlled simultaneously. For simultaneous 5-axis control, please use the F31iA5. The information in this catalog is valid as of May 2017. Specifications, accessories, safety device and function are available upon request. Some options are not available in particular regions. For details, please consult our sales representative. Flammable coolant such as oil-based coolant has a high risk of ignition, and will cause fire or machine breakage if ignited. If you have to use a flammable coolant for any reason, please be sure to consult our sales representative.